Installing A Bath tub
Installing A Bath tub
Blog Article
We have stumbled on this post on A Step-by-Step Guide to Installing a Bathtub below on the web and accepted it made good sense to share it with you in this article.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Installing a tub isn't specifically rocket science, however it does need strong plumbing, carpentry, and often, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately challenging job. If the old bathtub is conveniently available, the job can relocate easily; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either instance, the task is within a home handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the job and are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Opportunities are you might require an expert plumber to make tube links.
This post will certainly assist you set up a brand-new tub in your shower room if you have already purchased a new tub and do not require to transform the setup of your previous water pipelines.
Your devices as well as material checklist should comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a towel all set for the staying water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washing machines are in area between the faucet and the sink. Protect the faucet in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using the two wood boards under its feet, place the tub in the needed placement. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Activate the water as well as inspect all joints as well as new pipework for leakages and also tighten them if needed. Fill up the tub and additionally examine the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub ought to wait until the bath tub has been made use of a minimum of once as this will certainly settle it right into its final placement.
Preparing for the Installment
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its last position.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break a stiff seal, creating the water to pass through the wall between the bath and the tiling, causing issues with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealer can split rather very early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily available on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader on Installing A Bathtub, I thought sharing that article post was worth the trouble. Loved our posting? Please share it. Help other people find it. Many thanks for your time. Please come by our website back soon.
Click On This Link
Report this page